Ag AgCl Reference Electrode Silver Silver Chloride Φ6*140mm Glass Rod

In electrochemistry, in order for a specific reaction to occur, a stable electric potential needs to be applied to the working electrode. The potential of the working electrode should always be accurately controlled. This is why a reference electrode is needed as a potential reference standard. Common reference electrodes include Silver Silver Chloride Ag/AgCl reference electrode, saturated calomel electrode,Hg/HgO reference electrode, Hg/Hg2SO4 reference electrode and Non aqueous Ag+ reference electrode,etc.

The silver-silver chloride (Ag/AgCl) electrode is the most commonly used reference electrode. Compared with calomel electrodes that use mercury and its salts, Ag/AgCl electrodes are more environmentally friendly. Its electrode potential also has sufficient stability, reliability and reproducibility.

Special attention should be paid to maintenance and storage when using Ag/AgCl reference electrode. Before use rinse it with deionized water. If air bubbles are present around the porous frit, flick the tip several times to remove them. For cleaning use detergent (dish washing detergent with water), alcohols or acetone and rinse it with deionized water at the end.Compared with other reference electrodes, Ag/AgCl reference electrode is more sensitive to light. Therefore, when not in use for a short period of time, it is necessary to remove the rubber cap at the lower end of the Ag/AgCl reference electrode and soak it in a dark cup filled with saturated potassium chloride solution for storage. When it is not used for a long time, it is necessary to add a new filling solution to the Ag/AgCl reference electrode, cover it with a rubber cap, and store it away from light.

Check Details from here >> https://www.dekresearch.com/silver-silver-chloride-ag-agcl-reference-electrode-%CF%866*140mm-glass-rod-3011.html

Comments

What is the CO2RR Gas Diffusion Flow Cell?

The CO2RR Gas Diffusion Flow Cell (CO2RR GDFC) is a type of electrochemical cell used in the conversion of carbon dioxide (CO2) to other chemicals through a process called the CO2 reduction reaction (CO2RR). It is similar in design to the Gas Diffusion Flow Cell (GDFC) used to measure gas permeability, but it is specifically designed to facilitate the electrochemical reduction of CO2. The CO2RR GDFC consists of a small, sealed chamber with two compartments separated by a thin, gas-permeable membrane. One compartment is filled with a CO2-containing gas mixture, while the other compartment contains an electrolyte solution and a catalyst material, such as copper or silver, which facilitates the CO2RR. The two compartments are separated by the gas-permeable membrane, which allows CO2 to diffuse from the high concentration compartment to the low concentration compartment. The CO2RR is driven by an electric potential applied across the two compartments, which induces the reduction of CO2 int

What is the Gas Diffusion Layer (GDL)?

The GDL is a porous structure made by weaving carbon fibers into a carbon cloth (e.g. GDL-CT and ELAT) or by pressing carbon fibers together into a carbon paper. Many of the standard GDLs that are produced today come with a Micro Porous layer (MPL) and hydrophobic treatment (PTFE). The MPL and PTFE help with the contact to the membrane and with water management. The MPL typically provides a smooth layer with plenty of surface area for catalyst and good contact with the membrane. The MPL often uses PTFE as a binder that increases hydrophobicity, which helps keep the water within the membrane from escaping – drying out the membrane and causing higher resistance (lower performance). There is often an additional PTFE coating on the MPL surface to further augment this. What Exactly Does a Gas Diffusion Layer (GDL) Do? GDL essentially acts as an electrode that facilitates diffusion of reactants across the catalyst layered membrane. The surface area and porosity of the GDL is what

In-Situ Raman Spectroscopy Electrochemical Cell

In-situ Raman spectroscopy electrochemical cell is designed and manufactured for studying the in-situ spectra and morphology changes of electrode materials in electrochemical experiments. The working electrode is placed directly under the see-through window, so that the optical instrument can detect the working electrode from the quartz light window above the cell body. Commonly used instruments include optical microscopes, infrared microscopes, X-ray spectrometers, confocal Raman spectrometers, etc. According to different experimental test requirements, the in-situ Raman spectroscopy electrochemical cell is divided into four types: Single cell body with single light window type Single cell body with double light window type H type double cell body with single side light window type H type double cell body with double side light window type The single cell body with single light window type is the most widely used in-situ Raman characterization cell in DekResearch. It can be applied

Search This Blog